Find or Sell Used Cars, Trucks, and SUVs in USA

1988 Nissan D21 Hardbody Sr20det Blacktop Turbo Powered! Fast! Fully Restored! on 2040-cars

Year:1988 Mileage:260000 Color: White /
  BLACK/GREY
Location:

Anaheim, California, United States

Anaheim, California, United States
Transmission:Manual
Body Type:Pickup Truck
Vehicle Title:Clear
Engine:sr 20 det black top
Fuel Type:Gasoline
For Sale By:Private Seller
VIN: 1N6ND11S3JC315128 Year: 1988
Number of Cylinders: 4
Make: Nissan
Model: Other Pickups
Trim: HARDBODY D21
Options: Sunroof, CD Player
Drive Type: RWD
Mileage: 260,000
Exterior Color: White
Warranty: Vehicle does NOT have an existing warranty
Interior Color: BLACK/GREY
Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. ... 

Up for sale is a 1988 Nissan Pickup also known as the Nissan Hard Body Pickup. It is powered with a full SR20DET Black Top TURBO Swap running at 10psi of boost!!! FULLY RUNNING NO ENGINE PROBLEMS! This truck has a clean title, registration current till 1/31/14. Has a 5 speed transmission, No A/C, No Power Steering that's how it came from Nissan with no power steering. Chassis has about 265,000 or so but the swap has about 65,000 miles motor had about 45,000 miles when it was pulled from the front clip imported, mileage was verified! Please read more details about my truck below. Read carefully. 


YOU TUBE LINKS AT THE BOTTOM OF THIS LISTING!!! 
20 min Full walk around + interior HD video.  Slideshow pictures of this truck before it was restored! Link on the description to the slideshow. Cold start up, Engine Rev & full details on this truck!  



IF YOU WOULD LIKE TO COME SEE THE TRUCK IN PERSON YOU MUST MESSAGE ME A DATE AND EXACT TIME YOU WILL BE AT MY LOCATION. YOU WILL NOT BE ABLE TO TEST DRIVE THE TRUCK WITHOUT A SMALL DEPOSIT IN MY HAND OF 1000.00. ONCE THE TEST DRIVE IS OVER YOU WILL GET YOUR MONEY BACK, SINCE MY INSURANCE ONLY COVERS ME IF I CRASH THE TRUCK THAT IS MY INSURANCE IF YOU CRASH MY TRUCK! NO JOY RIDES! OR I CAN TAKE YOU OUT FOR A SPIN MYSELF


PLEASE READ MY COMPLETE LISTING! IF YOU DO NOT HAVE THE FUNDS  PLEASE DO NOT BID ON MY TRUCK! IF YOU HAVE ZERO FEEDBACK YOU WILL BE BLOCKED UNLESS YOU CONTACT ME NO EXCEPTIONS! NON-PAYING BIDDERS STAY AWAY PLEASE! SERIOUS BUYERS ONLY!

Now before you ask me any questions please please take the time to read all the details on this listing and view the You Tube video if your to lazy to read! If you have any questions i did not answer please message me. It took me about 1 full day to put all this together so please take the time to read this listing as i have put a lot of time into describing the truck and what I have done to fully restore this truck in the state it is now! Please do not ask me how i swapped the engine in my truck or if i can help you with your swap! There's plenty of info online to help you with your swap, my time is pretty limited so i don't want to be swamped with dozens of messages regarding trouble shooting or your swap. But anyhow... here we go full description below



HOW I GOT THE TRUCK


Ok so as stated the truck has a full SR20DET swap! Fully running with no engine problems! I got this Nissan Hard Body in 2006 from my cousin that used it as a daily beater. In 2006 i had a Nissan Titan and i was looking for a small pickup to drive back and forth to work since gas prices were high at the time and still are to the date but i figure this little Nissan will get a lot better gas mileage then my Titan! I asked my cousin if he would sell me his truck and he said yes ill sell it to you, so that was the start of all this madness! When I got the truck it wasn't the best looking truck, needed a lot of work lots of work to be exact but like any guy we love our project cars right lol! Posted a slide show video on youtube with few pics of what it looked like before the body was actually pretty straight just the paint was nasty original paint tho, interior was worn and old (ugly) needed a full restoration and i was actually thinking about not restoring this truck but like i said we love our projects right so i went ahead a took my money out of the bank and started this project!


PAINT AND BODY WORK


In late 2006 i started ripping everything out! took the whole interior out, removed all the glass, took all the moldings off, fenders off, hood off, bed off, cab stayed in place not messing with taking that thing off it was pretty much just a frame with a motor! By the time it was at the body shop it was early 2007 around April because i remember getting my tax return at the time taxes really helped me out with the cost of getting the paint and body work done. Sorry if i am making this a long story but its taking me back to memory lane and i'm trying to remember every detail. So i took it to the body shop and it took a few months to get it back, while it was there they made me aware of a few stuff that would help me save some money and speed up the process. I was told to replace the fenders and the hood, reason being was it was gonna cost more in labor to fix them then to buy replacements so that's what i ended up doing. Replaced the front 2 fenders and the hood i really didn't care they were aftermarket just wanted the truck to look its best! The tail gate was also replaced with an aftermarket tail gate lid because someone actually stole the lid. The rest of the truck of course is all original slight body work was done to make it as straight as possible, truck was fully prepped and blocked. Truck was fully shot taken apart, the interior, door jams, bed, were shot as if they were new. Truck was shot inside and out completely! We saved some paint by not painting the floor and part of the door where the door panel would cover it just a waste in paint.

The color code paint i used on this truck was the factory 2005 Nissan Titan Q10 Polar white blizzard, My Titan truck was white and at the time i had bought a tonneau cover that was not painted so i bought a full gallon of PPG Q10 paint for both of my trucks, painter said a full gallon would be more then enough to shoot my cover and my truck complete. If you know about paint once you reduce the paint it makes close to 1.5 to 1 3/4 gallons depending how it covers. Clear coat i bought was Glasurit clear! If you don't know about Glasurit clear coat search it online. Glasurit clear coat is top of the line clear coat and looks and shines just like glass! Look at my truck! Its been 5 years since they shot it and it looks new! Looks like this because its been garage kept it for years in my garage! 


INTERIOR


In late 2007 i started putting it all back together, this was very time consuming and it was a pain in the you know what if you know what i mean! I ordered new black carpet, new headliner and ordered all the door moldings inside and out! Took the bench seat and the door panels to this upholstery shop that a friend had recommended to me were they do good work. Bench seat and door panels were covered with vinyl black with dark grey see the pics, turned out pretty good. This truck has an aftermarket sunroof, it does not slide back and forth its an old pop up sunroof, the factory headliner did not fit perfectly and had to be modified to fit just a bit looks good to me. Got the carpet, door panels, window cranks etc etc the interior is done now its time to put the dash back on, before i did that i replaced all the vents on the dash. These vents were old and broke off so i had to get new ones from the dealer, tried the junk yard but they would always break off when i tried to get them off so i was forced to buy them new. I ended up painting the dash matte black with SEM paint, this paint does not scratch off if done properly, wasn't digging that ugly brown dash. The dash does have a crack on the top the rest of the dash is ok, i was gonna upgrade the dash to the new style dash but ended up not swapping the dash ended up keeping mine and covering it with a black dash pad so you cant see the crack on the top. Alpine CDA-9847 installed plays mp3 cd's and is I-Pod compatible with the correct cable. Steering wheel was replaced with an aftermarket steering wheel, that old Nissan steering wheel was huge not to mention brown so it did not go with my new interior, new hub and steering wheel was put in place. Horn does not work and Horn button is a knock off bride horn button.


EXTERIOR


After the interior was done started working on the exterior of the truck. As i had stated all the glass was removed, ended up having to replace the wind shield in the front because it was old and cracked when removing it, not only that but had lots of rock chips and kinda looked yellow so i was glad to see it go. Rear glass is the original glass and new molding was bought to give it a new tight seal. All the exterior door moldings were replaced as well. Cowl vent panels where the wipers are were also replaced with new OEM vents they were old and also broke when they were removed. Front end of the truck is the new style front end, new 1 piece bumper was bought, clear corners, clear turn signals, new chrome grille. Just recently put the projector style headlights on the truck looks really nice in my opinion, everything seems to look pretty good still. Lower valance is OEM and bumper brackets are OEM as well. Tail lights are after market altezza style black tail lights. Fiberglass roll pan (unpainted) installed ugly rear bumper removed, bed liner installed to keep the truck bed scratch free. New door lock cylinders were put on as well, the old cylinders were not working at all so ended up putting new ones. New mirrors & Outer door handles installed as well. 


SUSPENSION, BRAKES, WHEELS & TIRES


Truck was lowered with 2 inch lowering blocks, Air shocks are installed in the rear in case you have a heavy load also makes the ride a lot smoother. Front was lowered just about 1 inch turning the torsion bars down, new front shocks were recently replaced and have a lifetime warranty. Brake rotors are crossed drilled and slotted, these rotors have held in for quite a bit and still have a bit a life left. As stated i had a Nissan Titan and the wheels you see on the truck are my stock 18 inch dark grey Titan wheels. Wrapped them in 245/50/18 tires, nice and wide and not to low profile still give the truck a nice good ride. Titan wheels had to be bored out to make them fit on the hard body, believe it or not the bore is a lot bigger then the Titan wheel bore. Didn't want to run a spacer and have the truck shake at high speeds, they would also stick out which was not what i wanted it to look like. After i got them back they fit perfect looks like they came with the truck. Alignment was done at the time of wheel and tire install. 


ENGINE & SWAP INFO


What you all have been waiting for engine and swap details. This truck has a full black top SR20DET swap! So sometime in 2009 the stock 4 speed transmission on my stock Z24 which is the stock engine started taking a dump. I started looking for alternatives since i did not want to rebuild the stock transmission and in all honesty i wanted more power. Stock Z24 had about 240,000 miles on the original engine and still running strong but i started searching for swaps online and came across a SR20DET truck that was some sort of show truck with all these mods, finally i started doing some more research and came to the decision that this swap is what i wanted and i had to make it happen. First thing i did was rip out the old Z24 with the transmission then started shopping for my new swap. Didn't want to buy my swap on Ebay since if i bought it on Ebay i would be a nightmare returning the swap if it wasn't good, Ended up buying from a local shop that imports engines from Japan and it was not cheap at all. Bought the Black Top SR20DET engine with matching 5 speed transmission, complete wire harness, ignitor, mass air flow sensor & ECU from the shop with a full warranty. Got to hear the engine run before i bought it and fully tested it since i was gonna take more then 90 days to complete my swap. I told the shop owner about my swap and he told me he wanted to see it when it was done, also he gave me a number of a gentleman now a good friend of mine that does wiring for SR20DET's on full race & drift cars. 

When i started this swap i was pretty limited on time since i was working a lot and working quite a bit of overtime. 2010 rolls around and my swap is still not complete  then in mid 2010 i get laid off, for me it was not a bad thing but a good thing since i had plenty of cash and now would have the time to complete my swap. First thing i tested the swap in the truck and noticed the head was longer then my stock Z24 head and was hitting the firewall so I searched online and seen a few people saying the firewall had to be pushed back to make room for the engine. There are 2 ways of doing this 1. cut weld and fab up something pretty  2. sledgehammer   so sledgehammer it was lol. after hitting the firewall success fits all the way in and mounts line up. Before i bolted it down for good i replaced the clutch with a complete exedy stage 1 clutch kit, the stock clutch was still good but i was thinking way ahead and i did not want to undo the swap again when i could have done it while it was out so that's what i did. Resurfaced the flywheel, new rear main seal and it was ready. Bolted the swap down, routed all the hoses before hand because there is no room behind that wire wall. After it was bolted down noticed a lot of things that had to be modified, the transmission is longer so the stock shifter was further back. Had to buy new carpet again since the carpet would now have a hole in the wrong place, seat and carpet out again for the mean time to figure out the new configuration. Drive shaft had to be cut and shortened since the transmission was longer, Drive shaft was cut, welded and balanced by a professional shop. Rear end is the stock rear end, holding up perfect no issues. Pathfinder LSD can be put on but you gotta modify & cut the brakets off to make it fit correctly, you also may have to shorten the drive shaft since it looks like its a tiny bit bigger. Was gonna be my next upgrade but decided not to go thru all the hassle since the truck runs perfectly fine and has plenty of traction in the rear 

After i figure out the drive shaft and the shifter part that was done and i was on to the front for the car. I had a few decisions to make and all were pretty easy for me. 1. had to decide if i wanted to have A/C in the truck, decided not to run A/C because there was no room for the A/C condenser since i was gonna run a front mount intercooler. 2. Power steering was not installed with my truck from the factory and is manual steering which means you have to have some muscle to turn this bad boy on a complete stop, once its rolling this truck handles really really good better then any truck i have driven. 3. heater core was leaking from the inside and i ripped it out and did not replace it just looped the hoses and that was it. 

Cut up some aluminum pipe for the intercooler and made it fit the best i could, all the correct fittings where placed and fitted on the pipes so everything is working as it should. EGR system was taken off and not used. Front mount intercooler installed behind the front bumper looks like a radiator no one will ever know especially cops or highway patrol. Installed new Walbro 255 fuel pump had to do that since this swap requires more fuel. After we got all the plumbing down time for the fun stuff wiring, decided to call this guy up Dan that is a good friend of mine now at the time he was a stranger so i decided to give him a call to see if he can help me with the wiring part. Comes over and 3 hours later the truck is running and wires up my swap. My buddy Dan is no joke, wiring is full plug and play. No soldered wires, No cut wires, he used my factory plugs and swapped the wires into the correct plugs. If you ever need to take the swap out you can unplug the complete harness and re-connect it simple as that! Dan also wired up the cluster no make it work, everything works as it should. Reads fuel, temp,speed & tach.
Apex turbo timer was also installed at this time and it also works great, you can set the timer up to turn off the truck to allow it to cool down. Autometer Oil pressure & Boost gauges also installed to give you important engine vitals. HKS air filter installed, air filter element recently replaced. Greddy manual boost controller installed to adjust boost. Ebay blow off valve installed works pretty good surprised lol. Electric fan with flex a lite adjustable thermostat


EXHAUST

Exhaust in 2.5 in straight piping all the way down to a magnaflow muffler with a gibson stainless steel tip. No cat installed! It is straight pipe all the way down to a magnaflow muffler. Sounds nice and mellow on start up and mean at wide open throttle



WORK THE TRUCK NEEDS OR ADJUSTMENTS

1. motor is completely healthy runs strong no leaks. will need a new throttle position sensor or an ignition coil. when you open it wide open throttle around 4k to 4500 rpm the truck sounds like its bogging out or like misfire of some sort. if you drive it normal and don't open the whole throttle up you can rev it to red line but this only happens under a load. checked the intercooler pipes for leaks all is good unless its an intercooler leak which i doubt sometimes finding a leak in a pain in the butt, spark plugs changed so its not that. mass air flow sensor changed slight improvement. got it trouble shooted and its either a bad TPS or bad coil. easy fix once again motor completely healthy you can run any test compression or leak down test only before the auction closes not after don't want to deal with that after the auction closes.

2. tires are 40% up front and about 30 to 25% rear still have a bit of life will get you by for a while. only run 245/50/18 these tires are expensive especially this size, look on craigslist for some take offs that will save you alot of money. its up to you what tire size to run but i like the tires i am running right now since they have plenty meat and are wide for plenty of traction

3. door locks need to be adjusted, driver side locks but you will have to make some adjustments to it to make it open properly. passenger door disabled the handle so you can only open it from the inside still locks just can no be opened from the outside.

4. tailgate disabled as well, since it got stolen once i disabled one latch on one side. you can simply open the tailgate sticking a flat head and pulling on the handle, my anti theft mod lol

5. e-brake needs adjusting was working some time ago but does hold just a bit.

6. recommend changing the ebay shifter i put in, kinda loose but works fine. junk yard will be the cheapest option

7. anything you may want to change



SMOG, REGISTRATION & TITLE INFO

Truck is registered in California till 1/31/14 this truck is not smog legal in California, once again will not pass smog unless you know someone that can help you out! will not pass visual or emissions now if you ask me why it wont pass you shouldn't be bidding on my truck simple as that. Some states do no require a smog check but check with your local DMV or Highway Patrol to make sure you will not have any problems registering the truck. Truck as a clean title, clear of liens or tickets.



SHIPPING AND PAYMENT INFO

If you are an out of state buyer please have all your shipping quotes ready and have your transport company ready to pick up the truck within 3 days of full payment. I will require a full 500.00 deposit via Paypal after the auction closes, You will then have 2 days or 48 hours to pay for the truck in full. Method of payment is Cash on hand or bank wire transfer ONLY! Will not accept personal checks! Cashiers checks are ok but you will have to wait 7+ days for the check to clear the bank no exceptions! Will not accept paypal for the full payment amount!
Title will be sent Fed Ex 2 day air with signature required! Or title will be given in person after completed payment! 

IF YOU DO NOT AGREE WITH PAYMENT & SHIPPING DETAILS PLEASE DO NOT BID ON MY TRUCK SIMPLE AS THAT!




LIST OF MODS AND COST TO BUILD TRUCK

750.00   Truck cost
2400.00  Labor only Paint and body work includes wet sand and buff, primer, sand paper, prep work, shooting truck and some assembly
600.00   PPG paint, Glasurit clear, reducer, misc materials
2500.00 Full SR20det swap including wire harness,ECU, trans, ignitor, mass air flow
300.00   Dan's charge for complete wiring of engine, cluster wire up only and turbo timer wire up only
250.00   New windshield, fiber glass roll pan, bedliner
300.00   New fenders, hood, tailgate,headlights,grille,front bumper chrome,turn signals,tail lights
300.00   New Cowl vents, interior vents, new moldings inside and out, new headliner all OEM parts
250.00   Lowering blocks, Air shocks, New front shocks, Alignment, cross drilled rotors
260.00   Tires take offs, wheels free of my titan truck, bore out center hub at machine shop mount and balance wheels and tires, wheel locks with key
400.00   Upholstery, seat covered, cover door panels and bought carpet 2 times due to swap
200.00   Exhaust work with magnaflow muffler and tip included
375.00   Apex turbo timer, 240sx cluster, greddy manual boost controler, front mount intercooler, intercooler piping, blow off valve, oil and boost auto meter gauges, HKS filter w/ new filter
100.00   Alpine radio + speakers
150.00   Drive shaft cut & balance had to pay the guy a bit extra to come to my place and measure the driveshaft wanted it done right the first time
100.00   Electric fan with Flex a lite automatic on off switch adjustable thermostat
120.00   Walbro real fuel pump not knock off complete with filter
300.00   New stage 1 clutch kit complete with resurfaced flywheel and new rear main seal

9655.00 off the top of my head not including other parts!!!! Lots of money into this truck! That's what i cost me to build not what i'm selling it for! 


REASON FOR SELLING


Only reason for i am selling this beast is because the truck can not pull a trailer, im sure it can and it has plenty of power to do so but the payload and the frame is not ment for heavy loads! I have had lots of fun and have a lot of memory's in it. It has been a complete learning experience and joy to put my pride and joy together but there comes a time where you have to part ways with your vehicles and the time is now. I would like to find my truck a great home and someone that will take great care of it as i have for many many years. I would love to keep it but it just sits in the garage and this truck is ment to be driven and enjoyed! So if you think your that one lucky person bid on my truck it will not let you down plus to find another truck like this anywhere is nearly impossible especially in the condition it is in! I am the only person i know with this swap only and the only other people i seen are on you 
tube.   


YOU TUBE LINKS




GOOD LUCK! HAPPY BIDDING!




Auto Services in California

Yuba City Toyota Lincoln-Mercury ★★★★★

New Car Dealers, Car Rental
Address: 1340 Bridge Street, Browns-Valley
Phone: (866) 595-6470

World Auto Body Inc ★★★★★

Automobile Body Repairing & Painting, Used Car Dealers
Address: 140 N Coast Highway 101, Carlsbad
Phone: (760) 753-0035

Wilson Way Glass ★★★★★

Automobile Parts & Supplies, Glass-Auto, Plate, Window, Etc, Door Repair
Address: 2965 N Wilson Way, Salida
Phone: (209) 943-0325

Willie`s Tires & Alignment ★★★★★

Auto Repair & Service, Brake Repair, Tire Dealers
Address: 705 Monterey Pass Rd # B, San-Gabriel
Phone: (323) 604-0905

Wholesale Import Parts ★★★★★

Automobile Parts & Supplies, Used & Rebuilt Auto Parts, Automobile Accessories
Address: 10562 Walker St, Hawaiian-Gardens
Phone: (714) 827-6735

Wheel Works ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Tire Dealers
Address: 521 S B St, Montara
Phone: (650) 525-4517

Auto blog

2014 Nissan Pathfinder Hybrid priced from $35,110*

Sat, 26 Oct 2013

Nissan has announced pricing for the 2014 Pathfinder Hybrid, which was revealed earlier this year at the 2013 New York Auto Show. Offering two- or all-wheel drive, the hybridized crossover sports a 3.5-liter V6 and a 15-kilowatt electric motor, for a total of 250 system horsepower and 243 pound-feet of torque. Those numbers match up well with the 260 horsepower and 240 pound-feet of torque put out by the V6-powered Pathfinder. Naturally, fuel economy sees a hefty boost, to 25 miles per gallon in the city and 28 mpg on the highway, bumps of five and two mpg, respectively.
The Pathfinder Hybrid is available in three grades. Prices start at $35,100 for an SV and jump to $38,050 for the mid-level SL. A top-flight Platinum, meanwhile, moves the price up to $42,750. Adding all-wheel drive to the package bumps the price up to $1,600 across the range, and keep in mind that these prices don't include Nissan's $860 destination charge. Take a look below for the full press release from Nissan, including detailed pricing charts for both the Hybrid and V6 Pathfinder.

Toyota, Honda, Mazda and Nissan recall 3.4 million vehicles for faulty airbags

Thu, 11 Apr 2013

Most vehicle recalls that take place these days are a result of some problem that happens during the manufacturing process by the automaker, but as we see here, parts suppliers can also factor in to problematic safety issues. Automotive News is reporting that a total of 3.4 million vehicles produced by Japanese automakers between 2000 and 2004 are being recalled globally due to faulty airbags produced by an outside supplier, Takata Corp.
According to the report, vehicles from Toyota, Honda, Nissan and Mazda are being recalled because of passenger front airbags that do not inflate properly. Globally, Toyota is said to be recalling around 1.73 million cars including 510,000 in the US composed of Toyota Corolla, Matrix, Sequoia and Tundra as well as the Lexus SC430 for the 2001 through 2003 model years; this is the second time this year the 2003 Corolla and Matrix have been recalled for an airbag problem. Honda is recalling 1.14 million models, Nissan another 480,000 and Mazda 45,463. The article says that Takata supplied faulty airbags to non-Japanese automakers, but it did not specify which ones.
Honda and Toyota have released information on their own websites about the recall, while Nissan and Mazda have not yet commented. Read official press releases from Honda and Toyota, below, and look for updates as we have word from the others.

Nissan Kicks concept debuts in Sao Paulo [w/videos]

Tue, 28 Oct 2014

The Sao Paulo Motor Show only comes around once every other year, and Nissan - an automaker deeply vested in the Latin American market - isn't missing out on the opportunity to showcase a new crossover concept.
Called the Kicks concept, the crossover seems to slot in size-wise in between the Juke and the Rogue. Nissan isn't saying much about it, though, aside from its having drawn its inspiration from Brazil with a "satin titanium" finish and bright orange trim - the former taking its cues from Sao Paulo and the latter from Rio.
While emphasizing its Brazilian character, Nissan also stresses that the concept's creation was "a product of global collaboration." So while it isn't saying anything about production feasibility, it is seemingly suggesting that if it were put into production - and as we stated previously, we think it just might - it could stand to be a global model and not confined strictly to South America.