Sub Model: SS
Exterior Color: Red
Interior Color: BLACK
Trim: SS 396
Number of Cylinders: 8
Drive Type: RWD
Tucson, Arizona, United States
I'm selling my 68 camaro that I bought 8 years ago,in bad shape,some small rust issues in the lower quarter panels ( my body man took care of that ) so I did some research and came to the conclusion that is a ss 396 , this camaro came originanly with the m22 manual trans. this transmission has the speedo cable inlet on the right side so the cable had to came out behind the distributor ( the hole is still there) and a big block 396 but when I got it motor and tranny were long gone, so I put a 396( unknown milage but runs strong ) out off a 70 camaro or chevelle? and a th 400 auto. painted it matador red (code RR ) that is the original color and black houndstooth interior also original in the car, ( code 749 ) I also installed a center console with after market gauges, the car has all polyurethane bushings motor mounts and trans. mount 750 holly street avenger double pumper,preformer rpm intake, a mild came headers, 2 1/2 flowmaster exhaust,lakewood traction bars, stainlees steel gas tank,rallyes 7"s front 8's out back with drag radials, this car drives great with no vibrations or rattleling of any kind, is not a show car just a driver that turns heads everywhere,
I forgot to mention that the car has front disc brakes, 12 bolt rearend, painless wire harness and the trans. was rebuilted a few months ago! all the weatherstrip was replaced, I think that somebody that owned it before me used to race this car it has weld marks on frame from subframe connectors and they trim and patch the rear floor pans (doesn't look bad do) also the nuts that hold a pin down hood are still there, if you have any ?'s you can call me at home 520-5785435 after 4:00 pm tucson time thank's again!
a couple of small issues the car has ,one of the heater control levers broke loose ,the driver rear quarter window needs one of the guide rollers needs to be replaced ( I have it in the glove box I just haven't had time to put it on I'll try this weekend ) ,I drive this car about 6 or 7 times a year, on nice days, it's allways in the garage and covered
I did so much to this car that I keep forgeting! I installed new front fenders, hood ,valance and header panels, grill trunk lid, front and back bumpers,all badges ,front and back windows, one more thing! the car is listed for sale localy so I may end this auction at any time, thank's
Domestic manufacturers enjoyed a good year for heavy-duty pickup sales in 2012. PickupTrucks.com has taken a close look at exactly how those sales broke down between each manufacturer and between three-quarter and one-ton pickups. Ford sold some 67,786 F-250 Super Duty models last year with the Chevrolet Silverado 2500 HD falling just behind at 56,359 units. The Ram 2500 HD came in third at 41,918, while the GMC Sierra 2500 HD earned itself fourth place with 27,616 deliveries. While Ford held onto the top spot in the one-ton market, Ram easily nailed down second place by selling more 3500 HD models last year than General Motors sold Silverado 3500 HD and Sierra 3500 HD trucks combined.
So, did GM manage to sell more trucks than Ford with its two brands? Very nearly. Ford sold a total of 119,338 heavy-duty pickups to GM's 111,555. Ram, meanwhile, moved a distant 77,583. But perhaps more interesting is the diesel take rate in this segment. PickupTrucks.com says 80 percent of all domestic one-ton trucks roll from the dealer lot with a turbo-diesel under the hood. Head over to the site for a closer look at the breakdown.
It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.
Do not adjust your computer screen, you are not seeing the rebirth of the Pontiac brand. General Motors has chosen to use a G8 to disguise a test mule for the latest prototype of the forthcoming Chevrolet SS. The G8 was closely related to the Holden Commodore and Vauxhall VXR, the platform upon which the new Chevrolet performance model will be based. It should come as little surprise, then, that GM has opted to use the cladding from the former G8.
Thought the front clip of this mule is pure Pontiac, note the vents immediately behind the front wheel. That is a distinctive design hallmark of the Vauxhall VXR. Also note that this vehicle is right-hand drive, as the Holden and its Chevy counterpart will be very closely related. That likely includes potential drivetrains. The spy photos of this mule also reveal very wide rear tires, and rear wheels that do not match the fronts.