1969 Ford Torino Gt Fastback on 2040-cars

Auto blog

2014 Ford F-150 gets CNG option

Ford is toiling away, installing heavy-duty engine components into select 3.7-liter V6s to allow them to run on compressed natural gas (CNG) and liquid petroleum gas (LPG) in addition to gasoline. That's nothing new, but now, Ford has announced that it will offer the 2014 F-150 with this engine configuration, bringing the Blue Oval's total number of CNG/LPG-friendly vehicles up to eight. The F-150 will be the only half-ton pickup on the market that can run on these gases.
Ford will charge $315 per vehicle to equip the optional engine, but the trucks won't be ready to run on the alternative fuels straight from the factory and must be upfitted with additional equipment. A Ford Qualified Vehicle Modifier will install a separate fuel system for the compressed gases at a cost of $7,500 to $9,500, depending on fuel tank size. With the right-size tank, the F-150 equipped with the CNG/LPG-prepped engine can go 750 miles on one tank of gas, according to Ford, averaging 23 miles per gallon.
The practice of offering flex-fuel vehicles is gaining momentum as businesses take advantage of cheap gas. CNG can be bought for $2.11/gallon on average (per gasoline equivalent), and sometimes for as little as $1.00 in some parts of the US, Ford states. "With the money saved using CNG, customers could start to see payback on their investment in as little as 24 to 36 months," says Jon Coleman, Ford's fleet sustainability and technology manager. The automaker expects to sell a total of 15,000 CNG/LPG-prepped vehicles in the 2014 model year.

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

Ford announces four recalls, 1.4M vehicles affected

Ford is taking a bit of the spotlight away from General Motors, announcing a major group of recall campaigns, covering a total of 1.4 million vehicles built between 2006 and 2013.
Let's start with the big one, which covers the Ford Escape, Mercury Mariner and, according to The Detroit News, Ford-built Mazda Tribute CUVs. 915,216 vehicles are covered, all of which were built in model years 2008 to 2011. 736,000 vehicles are in the US, while Canada then Mexico make up the vast majority of the remainder. The problem is due to an issue with the torque sensor in the steering column, which could lead to sudden power steering failure. Manual steering would still be available, though.
"Dealers will perform one of three service fixes, depending upon what diagnostic codes are shown when the vehicle is taken to the dealer," Ford spokeswoman Kelli Felker wrote to Autoblog in an email. "They will either update software for the power steering control module and the instrument cluster module; replace the torque sensor; or replace the steering column, which includes upgraded power steering control module software."