1930 Model A Ford 2 Door Sedan Stock Motor Good Condition Belongs To Aj Foyt on 2040-cars

Auto blog

Ford investing $500M in engine plant for 2.7L EcoBoost production

Ohio is a hot area for Ford at the moment with the announcement just a few weeks ago that production of the next-generation F-650/F-750 medium-duty trucks would move from Mexico to the Ohio Assembly Plant in Avon Lake, Ohio. Now, Ford is investing $500 million to hire 300 workers at its Lima Engine Plant in Lima, Ohio, to add production of the twin-turbo 2.7-liter EcoBoost V6 for the 2015 F-150.
The latest investment will be used to add a new flexible engine assembly system and renovate 700,000 square feet of the plant for machining and assembly areas. The Lima factory already builds Ford's 3.5-liter and 3.7-liter Duratec V6 engines. The plant opened in 1957, and it's on track to build its 40 millionth engine later this year.
Ford claims that the 2.7-liter EcoBoost will offer V8 performance with better efficiency in the F-150. It comes standard with intelligent stop/start that doesn't activate when the truck is towing or in four-wheel drive, and it's made from a combination of compacted graphite iron and aluminum for low weight and high strength. The company says that V6 engines have already proven popular in the F-150 with 57 percent of trucks in 2014 being equipped with either the naturally aspirated 3.7-liter or turbocharged 3.5-liter EcoBoost engines.

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

3dCarbon now offering body kit for Ford Fusion

A factory-backed body kit by 3dCarbon is now available to Ford Fusion owners who want their car to stand out from the crowd while not being too flashy. The body kit adds a more aggressive front spoiler, side skirts, rear body trim and spoiler that are, in fact, integrated quite nicely into the Fusion's already-comely styling, just as 3dCarbon claims. All Fusions with the kit also receive dual exhaust ports with the stainless-steel exhaust surrounds usually reserved for the Titanium package Fusion EcoBoost models.
A nice detail of 3dCarbon's injection-molded urethane body kit is that it has undergone crash testing to certify that it can withstand crashes up to five miles per hour. Because of this, the kit is warrantied by 3dCarbon for five years or 50,000 miles, much like Ford's warranty on its own parts. In fact, the kit is available through participating Ford dealers and can be financed through Ford Motor Credit. Buyers can purchase the kit - pre-painted or unpainted - and install it themselves, or it can be purchased with a new Ford Fusion and installed at the dealer, pre-painted to factory specifications. Of course, it can also be ordered directly from the source. Take a look at the press release below for more detailed information on the body kit, and let us know what you think of it in Comments.