1966 Ford Fairlane 500xl 393 Stroker Motor Racing Heads (better Than Mustang) on 2040-cars

Auto blog

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

Ford recalls 434k vehicles for several unrelated issues

It seems that the hard winter in much of the country has been as rough on some Fords as it has on many people. The Blue Oval is recalling roughly 434,000 vehicles in two separate recalls, and one of them partially caused by the salt used to melt the snow on roads.
The first recall covers 385,750 2001-2004 Escape models in the Midwest, Northeast and Canada because a subframe could rust and eventually fail. This is partially due to the road salt used in those areas, and about 349,000 of the affected vehicles are in the US. To remedy the problem, dealers are installing a reinforcement cross brace on the frame to strengthen them. There has been one crash caused by the failure but no injuries. According to The Detroit News, this is not the first rust-related recall for Ford. It estimates the company has repaired over two million vehicles since 2010 for problems on vehicles related to the iron oxide, including the rear wheel wells of the Freestar minivan.
The second recall covers 48,950 2013-2014 Ford Fusion, Escape, C-MAX and Lincoln MKZ models because welds in their seatbacks don't meet National Highway Traffic Safety Administration standards. The fault affects the front seats, and the sub-standard welds joining the setback to the recliner could increase the chance on injury. There have been no reported injuries or accidents caused by the problem, but there are 42,972 affected vehicles in the US and 4,744 in Canada.

Ford celebrating 80 years of Aussie utes as it prepares to shutter Oz manufacturing

Ford is ending Australian production after 90 years in 2016, and with it may go perhaps the most iconic vehicles in its auto market - the ute. Car-based pickup trucks like the Ford Ranchero and Chevrolet El Camino were always more of a curiosity than a true market force here, but in Australia, they have long proven hugely popular.
As the legend goes, Ford invented the niche after a farmer's wife had asked Ford Australia's managing director for a more utilitarian car. Her request was simple: "My husband and I can't afford a car and a truck but we need a car to go to church on Sunday and a truck to take the pigs to market on Monday. Can you help?"
Ford's design team came up with a two-passenger, enclosed, steel coupe body with glass windows and a steel-paneled, wooden-frame load area in the rear. The sides of the bed were blended into the body to make it look more unified, and to keep costs down, the front end and interior were based on the Ford Model 40 five-window coupe. Power came from a V8 with shifting chores handled by a three-speed manual. Within a year, the new vehicle was ready, and production began in 1934. Lead designer Lewis Bandt christened it the coupe-utility.