For Sale By:Private Seller
Number of Cylinders: 8
Drive Type: Four Wheel Drive
Exterior Color: Green
Nampa, Idaho, United States
For Sale 1972 Ford F250 4x4 Highboy. Has a 460cu with a carter afb 4 barrel carb, 4spd trans, divorced dana 24 gear driven transfer case. I has all new brakes in the front axle along with new kingpin bearings. Has power steering but manual brakes. stops well just takes more effort than one with power assist. Also the truck is a aircab! Has all the dash air conditioning parts but would need a compressor to get a/c working. The truck does run and drive and steers real tight. Could use a tune up as it does miss fire randomly. I just installed a new timing set, fuel pump, starter, and starter solenoid along with rebuilding the front axle. Has good potential for a restore or just drive as is. Tires are also at about 50% all 4.
Vehicle is in Nampa, ID and can be seen if needed. Buyer is responsible for pickup or shipping and vehicle is sold as-is no warranty
The Ford GT40 owns a firm spot on the list of the greatest American racecars ever made, being the first car from the United States to take an overall win in the 24 Hours of Le Mans. And now Mecum will auction what it claims is second-oldest GT40 still in existence at its Houston sale on April 12.
The story of the GT40 is fascinating. Henry Ford II attempted to buy Ferrari in the early '60s, but Enzo refused. Ford decided if he couldn't have them, then he would beat the Prancing Horse on the track. Ford went to Carroll Shelby and asked him to spearhead the program. The early cars combined a steel monocoque chassis with Ford's 4.2-liter V8 engine pumping out around 350 horsepower. The first prototype made its public debuted on April 1, 1964, at the New York Auto Show.
Shelby kept building prototypes, including GT/104, which is for sale here. This version featured a lighter steel chassis and was raced at Le Mans in 1964. However, a fire forced it to retire. It was then repainted and had a 4.7-liter (289-cubic-inch) engine fitted. The chassis had its best finish at the 1965 Daytona Continental 2,000 Kilometers where it finished third with Bob Bondurant and Ritchie Ginther behind the wheel. Later that season, it was shipped back to Ford where it was restored and displayed at auto shows until 1971 when the automaker sold it. Since then, it has had many private owners.
It's a fairly well known fact that removing weight from a car is essentially a panacea for many of the modern automobiles problems. Does it handle like crap? Remove weight. Underpowered? Don't add power; trim the fat. Need to improve fuel economy? It's diet time.
Actually executing a major weight reduction program, though, much like with human beings, is no easy task. Unlike you or I, where motivation is the issue, the prohibitive measure in trimming a car's waistline is money. Lightweight materials are expensive, with carbon fiber and carbon-fiber reinforced plastic still primarily in the domain of higher end vehicles. Even aluminum construction, pioneered on a mass-produced level by Audi and Jaguar, is only now starting to make its way into the mainstream, thanks to the upcoming Ford F-150.
With this concept, though, Ford is attempting to show that a mass-produced, lightweight vehicle isn't too far off. This is the Lightweight Concept, and while it may look like a Fusion, it weighs as much as a Fiesta. For reference, the lightest Fusion available to the public is the 3,323-pound, 2.5-liter model with a manual transmission. A manually equipped, 1.6-liter Fiesta, meanwhile, is just 2,537 pounds.
Mays is by far not the first designer to use heritage design cues in his work.
The announcement that J Mays will be leaving his chief creative officer role at Ford Motor Company on January 1 ends a 13-year run in one of the industry's top design roles. While best known for having a hand in reborn classics like the Volkswagen New Beetle, Ford Mustang and Thunderbird (above), Mays' legacy is more complicated and nuanced than being considered the father of what is known as "retrofuturism".