2007 Dodge Ram 2500 Slt Crew Cab Pickup 4-door 5.7l on 2040-cars

Auto blog

Dodge Scat Pack for 5.7L Hemi V8 detailed, priced

Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.