2006 Dodge Ram 2500 Cummins on 2040-cars
Alamosa, Colorado, United States
2006 Dodge Ram 2500 4x4 SLT.
Engine:
Number 4 cylinder burned a piston so the motor was taken to Mountain High
Performance in Arvada Colorado. Mountain high is a respected shop and Bill, the
owner, has built Cummins motors that have powered trucks to 9 second quarter
mile passes. The cylinder head was gone through, and all cracked were repaired.
The head was given a big valve conversion to increase flow. New seats were
also installed, with 1.340 oversized valves. All guides were repaired as needed,
and the head was decked to .008”. Some light porting/polishing was also
done.
The block was boiled, and cleaned, and the burned cylinder was sleeved, and
everything was bored to .040 over. Each cylinder was honed to fit each piston,
and they were numbered in order so they were all fitted to their respective
cylinders. All bearings were also replaced.
The engine was balanced, and the crank, cam, drive gears, push rods, connecting
rods, pistons, rings, main bearings, oil pump, and sleeve were all cryogenically
treated to increase the harness of the material. Freeze plugs were also threaded
to prevent them from popping. ARP 425 head studs and main studs were used. Cam
shaft is a Hamilton 188 cam, with their valve springs, and HD push rods. The
connecting rods used were new 12 valve rods that were shot peened and cryo
treated.
The machine work alone ran a discounted cost of 8,608, which would have easily
been over 10,000 had I not worked in the same industry and dealt with the shop
on a day to day basis.
Aftermarket parts:
ATS Stage VI transmisison. Billet shafts, flywheel, co-pilot, five star
converter, and deep pan. Trans was gone through less then 100 miles ago at
ATS. $8,580
ATS Aurora 5000 Turbo Kit $2,087.27
ATS Twin CP3 kit $2,350
ATS Exhaust Manifold $495
Hamilton 188 cam $699
Hamilton Push Rods $275
Hamilton Valve Springs $399
ARP 425 Head Studs $430
FASS 220GPH Titanium fuel system $860
Dynomite 220HP Injectors $4,000
Beans Diesel Fuel Sump $149.95
Starlite Diesel Autocal with Custom Tuning $795.00
Fuel Rail Cap $50
Autometer C2 gauges
-Boost
-Pyro
-Drive Pressure
-Trans Temp
-Drive Pressure
-Fuel Pressure
—— All in a overhead pod and a pillar pod
— — Total: $842
Nitrous kit with custom painted bottle and billet bracket (never used on this
motor)
$600
Cal Trac Traction Bars $419.00
H2 Wheels $400
Custom stack with FTE resonator $560
Total parts: 23,941.54
Machine Work: 8,608 (heavily discounted)
Labor was all done myself, but would cost someone somewhere around 4000 for all
of this.
What it would cost you to build this truck, not including the truck,
approximately, $36,549.54, and that is with heavily discounted machine work.
This truck, by itself, with only 34K miles, would fetch somewhere around $30,000
is my guess. That is $66,549 if you had to go out and do all this yourself!!!
This is a heck of a deal.
Truck has not been dynoed, on it’s old setup with stock head and cam it made
730 rear wheel horsepower on fuel and 918HP on nitrous on bulldog tuning. The
best previous time, it has not been ran since, was a 11.2@124mph. This is a easy
10 second truck now.
As I said I am the original owner of this truck. It was purchased while I was
a senior in high school, and I love it. Sadly I am relocating to California and
need to afford some expensive real estate. Truck really needs nothing but a new
owner.
Truck does not have a bumper in the pictures, it will have a painted to match
roll pan on by the time the auction ends, done by a reputable shop. Really the
only issue with the truck is a few small rock chips along the very lower rockers
from a dirt road, and a very slight scratch on the front right fender. Interior
isn’t perfect, but it looks pretty darn good for 10 years old. For the past
three years I have worked at one of the largest diesel performance shops in the
area, this truck is done right
Dodge Ram 2500 for Sale
2000 dodge ram 2500 laramie slt(US $8,000.00)
2002 dodge ram 2500 quad cab slt cummins(US $17,500.00)
Yes(US $18,000.00)
2014 dodge ram 2500(US $26,950.00)
2006 dodge ram 2500 laramie(US $14,700.00)- No title(US $4,500.00)
Auto Services in Colorado
Windsor Car Care ★★★★★
West Side Auto Body & Towing ★★★★★
Toyexus Service ★★★★★
Tito`s Cash for Cars ★★★★★
Suzuki-Mccloskey ★★★★★
Red Rock Auto Clinic ★★★★★
Auto blog
Are you the Dodge Dart SRT4?
Tue, 08 Jan 2013Dodge has just confirmed that it will be bringing its newest Dart variant, the Dart GT, to Detroit next week, but we're still in the dark about when we'll see a truly hotted-up SRT4 version. But now, by way of the rumormill anyway, we've got at least one proposed, potentially Dodge-based rendering to light our way.
Seen here is what would appear to be a design sketch of the SRT4 Dart. Obviously the image that has surfaced is of rather low-resolution, but there's at least some evidence to support that it may be legitimate. In the original picture, one can just make out the name Tim Doyle in the lower right corner. As it turns out, Tim Doyle's name is also watermarked on the final design image for the 2011 Dodge Durango Citadel Black & Tan, a model that was shown at SEMA in 2010.
Of course, even if this really is the work of Doyle, there's nothing to say that this image isn't one of a great many potential looks for the future SRT4. In fact, the departure of the cross-hair grille from the Dodge's nose seems like it could be a hard sell, though we do, naturally, dig the sleek hood scoop and the bulked up wheel/tire combination.
Dodge Viper recall requires small-handed mechanics
Fri, 25 Apr 2014It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.
Dodge Viper to out-Hell the Hellcat with supercharged V10?
Wed, 20 Aug 2014The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.