1989 Dodge W350, 4x4, 5 Speed, Fully Restored, 19.5" Wheels, Pipeliner on 2040-cars

VIN: 1b7mm3654ks052376 Year: 1989
Make: Dodge
Model: Other Pickups
Cab Type (For Trucks Only): Regular Cab
Trim: 2 door
Options: Cassette Player, 4-Wheel Drive
Drive Type: 4x4
Power Options: Air Conditioning
Mileage: 12,000
Sub Model: W350
Exterior Color: White
Disability Equipped: No
Interior Color: Tan
Warranty: Vehicle does NOT have an existing warranty
Number of Cylinders: 8

Condition: UsedA vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections.Seller Notes:"Fully restored, with about 12,000 miles of use."

1989 Dodge 4x4 W350 cab chassis, with custom flatbed. I bought and restored this truck from the ground up, using all original parts, NOS mopar, or american made replacements. I built this truck with the intention of doing mobile welding work. I could have went out and bought a newer truck for less money than I ended up in this one, but I wanted something unique and something that was still a truck. I never thought I'd be selling it, but things have changed, and I have too many vehicles to take care of. Trucks don't get much tougher than this, Dana 60 front, Dana 70 rear, throttle body injected 360ci motor, NV4500 5 speed, NP205 transfercase, 1410 u-joint rear shaft. This truck would be a good candidate for a late model hemi or cummins swap, that's the only thing that could make it any better. The truck was all original when I bought it, with about 119,000 miles on it. I took it down to the frame and rebuilt and repainted everything as I went back together. I replaced the original 16" wheels with 19.5" with new Bridgestone tires, I replaced the 727 automatic with a NV4500 5 speed from a 96 Dodge truck, I got rid of the knapheide work bed that was on it and built the custom flatbed that is on it now. The bed is set up to hold three welding cylinders, and hinges out of the way to make replacing them easier. Comes with the highway products tool box that cost $500 new by itself. The body was stripped to bare metal, paint is base coat clear coat. Axles were tore apart and rebuilt with new bearings and seals, I added a Dana Power-Lok posi in the rear, both axles still have their factory 4.56 gears. Engine was bored .040 over, crank reground, heads rebuilt with new valves and seats, new roller cam and lifters, double row timing chain, new bearings, oil pump, seals, gaskets, water pump, etc.. New SFI billet steel flywheel, new clutch and pressure plate, throw out bearing, new clutch hydraulics. Transmission was taken apart, cleaned, inspected, resealed, and repainted. Transfercase has new seals, new-New Process output shaft, new bearing, and yoke. Driveshaft has been rebuilt with new spicer U-joints, rebalanced and trued. Brakes are all new, new master cylinder, new shoes and pads, rotors and drums turned. Power steering box and pump were disassembled, cleaned, inspected, and resealed with new parts. Has new in-tank fuel pump and all new hoses. Radiator has been recored with new heavy duty 3 row core, biggest that will fit in stock tanks. Exhaust is custom built from aluminized mandrel bends and straight tubing, with stainless magnaflow mufflers. Interior has been redone, seat frame sandblasted and repainted, then new upholstery, dash and door panels redyed, new rubber floor mat. All wiring has been gone through, inspected, retaped, dielectric grease applied to all connections. Air conditioning blows ice cold, new compressor, dryer, evaporator, new hose. New heater core and heater control valve. I think I could go on and on, but I think I covered all the major stuff. Every single piece and part of this truck has been gone through. This isn't just another repainted truck with a new seat cover claiming to be restored. I did all the work myself, and had no intention of selling, so I didn't cut any corners. If you have any questions, or want more pictures of something please contact me. I have over 12,000 in this truck in just parts alone, not counting the hundred of hours of labor it takes to restore a vehicle to this level. The reserve is set at a realistic price, I know I wont get back all that I have in it. Old trucks are only worth so much, but someone who understands how much work it takes to do this, will know that they are getting it for a steal! Also comes with a spare wheel and tire, and another spare wheel, both painted and ready to go. Truck currently has about 12,000 miles on it since I finished it.