All Power Automatic Cd Player Financing Available Warranty Off Lease Only on 2040-cars

Auto blog

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

2013 Dart GT will hold us over until SRT stokes Dodge's handsome compact

No, this isn't quite the Dart SRT4 we've been waiting for - and still believe is coming - but as part of its 2013 Detroit Auto Show lineup, Dodge will be showing off the slightly sportier Dart GT seen here.
Building on the already well-equipped Limited model, the GT adds performance enhancements including a more powerful engine, 18-inch aluminum wheels, sport suspension calibration, unique front fascia and dual exhaust. Inside, you'll find perforated Nappa leather seats, a heated steering wheel and front seats, dual-zone climate control, remote start (if you spec the automatic transmission), Chrysler's 8.4-inch Uconnect touchscreen, a seven-inch TFT display in the gauge cluster, and a whole lot more. Optional goodies include hyper black aluminum wheels, a technology group (pushbutton start, keyless go, rain-sensing wipers, blind spot monitoring and smart-beam headlamps), power sunroof, Sirius radio, Garmin navigation, Alpine premium sound and high-intensity discharge headlamps.
Powering the Dart GT is Chrysler's 2.4-liter MultiAir2 four-cylinder engine producing 184 horsepower and 174 pound-feet of torque. That grunt is sent to the front wheels via a standard six-speed manual transmission, but a six-speed automatic 'box is optional.