Project Car: 1933 Chrysler Cq Rumbleseat Coupe - Body #253 Of 364 Made >>rare<< on 2040-cars
Jersey City, New Jersey, United States
IF YOU DIDN'T GET WHAT YOU WANTED FOR CHRISTMAS>>> Just for you - or your
favorite wrench-turner - is a serious project that will make you the envy of
the car show circuit. In 1933,
Chrysler produced only 364 of these CQ-model Imperial Rumbleseat Coupes. This is Body #253. Body by Budd, more widely known for railway cars. Interestingly, there was a mid-year design
change, documented in service manuals and bulletins, which indicate that this
was the last of the original design run, and #264 was the first of the revised
design. 308Cubic Inch Straight-Eight engine with clean bores; Three-speed transmission with the Freewheeling Clutch, power hydraulic brakes, and unbroken glass in the instrument panel! There are several unused NOS replacement tires, along with NOS tubes and rim strips. Some new replacement switches and brushes, including five Vintage NOS Wagner brake light switches. Two Correct Headlights included, which I purchased in 2000 at the Allentown County Fairgrounds Winter Swap Meet. Replacement bearings for the rear axle. The original temperature gauge is not show in the photo pf the gauge cluster, but is also included - if you look in the photo where there is a piece of cardboard tube taped with blue tape, that is the box containing the temperature gauge with the bulb assembly. Also included are the elusive Radiator Grille Badge AND Crank Start Handle Hole Cover (See Photo #5 (If you buy this car, the original PRISTINE Owner's Manual in the picture is available separately for what I paid for it in 1995: $200.00)). Also included in this auction are four (4) hubcaps (I paid $60.00 each in 1995) and a full engine gasket set, both purchased from Kanter Automotive in Boonton NJ. Unfortunately, the radiator cap hood ornament was long gone before I bought the car. I could put up another 40 photos of all the parts that I disassembled and removed from this car, but you can only put up 24 photos. . . Is it rough? Sure it is – but then you wouldn’t be in too good condition if you sat outside for 15+ years in Jersey City either!!! Please note that Photograph #2 is this car just before I had it towed off the outside lot where it had sat all those years.
The car is disassembled, off the frame, and approximately
90% complete - if you don't count the upholstery, glass, and wood, which rotted
away in the elements before I tracked down the owner and obtained a clean,
valid New Jersey title, then rented a garage and began working on my "dream
car". But life happens and I ran out of
time to work on her (Wow - that whole work and career and family thing after
finishing college. . . who knew???). The reserve price is the purchase price I paid for the car originally - it does not include any other parts I purchased, work I had done (there was a little), or garage rent I paid over the years! HERE IS THE SOB STORY - Skip down to the *** if you don't want to bother reading. . . So, I haven't really worked on her in the last almost 20 years. I have been more of a caretaker of this rare, historically interesting vehicle (AND paying rent on the garage!) for whoever is that lucky person who will bring her back to her original glory. Definitely not a belly-button car!
I had seen this sitting in a lot in the middle of
urban sprawl and decay for a while, but when I noticed that the local punks had
smashed out the windows and knocked off one headlight, I decided that I had to
save her. I was working full-time, going
to college at night (no student loans - Paid out-of-pocket!) and I managed to
scrape up and eventually I was the proud owner of a sorry-looking pile of
60-year old metal. I began disassembly -
that is really cheap to do - and acquired some almost-correct headlights for an
exorbitant price. I got a reproduction
service manual, and an original owner's manual, as well as several original
Service Bulletins. A couple of
suspension parts got sandblasted and powder-coated, I bought some bearings for
the rear axle, and then, for personal reasons, work stopped. And never re-started.
At least she was inside, mostly in the garage, while some other parts made it into my basement (Transmission, luggage rack, radiator, grille, Watson Stabilators, generator, starter, carburetor, and boxes upon boxes of other small parts, plus some other odds-n-ends). ****************************************************************************************************** I took photographs of the disassembly process and logged them step-by-step in a notebook, to aid in future re-assembly. I also tagged all the parts for identification as I removed them.
If you don't know what they are or where they came from, it ain't too easy to put 'em back, y'know?
Anyway, it is time for this diamond-in-the-rough to move on to the next stage of her life, as we part ways and my family and I move on to the next stage of our lives.
Please contact me with and questions comments or additional information if you can provide any.
SHIPPING: I WILL NOT SHIP. PICKUP ONLY.
Pickup will involve preparation, coordination (in
order to access the garage, which is normally blocked by residential tenants
parked in the driveway in front of it), a large box truck (A power lift gate would be a HUGE HELP!), and helpers. A FLATBED IS NOT ADVISABLE WITHOUT A VAN OR ANOTHER ENCLOSED TRUCK AS WELL. Tie-downs, dollies and moving blankets are a
really good idea. There is an engine
hoist in the garage available for use, and with creativity, patience, and an
eye for safety, everything can be loaded from ground level. Consider that this is how I removed the body
from the frame by myself, without damage or injury (other than the typical
scraped knuckles normal to playing with cars).
I will also need to get everything I have at my house over to the garage
for easy (ha!) one-stop pickup. I will be doing that movement over the next several days. The body is on a dolly constructed of 2x4s and dolly wheels, which makes it easier to maneuver the body around. The engine is on a dolly from a piece of vintage medical equipment, and goes with the engine too.
This will likely be an all-day affair. Plan accordingly. Weather should always be considered as well. While there is no great pressing need to move immediately, we do need to be reasonable and do it fairly soon. My schedule is very flexible after January 15th, 2014.
PAYMENT: To minimize any problems, I would advise that we use the escrow service recommended by eBay: Escrow.com. Now, if you just want to PayPal me the full amount upon end of auction and are willing to trust me with your money until you make the pickup, I have no problem with that! But I think that using the escrow is the most advisable course. We can split the fees.
|
Chrysler Imperial for Sale
- 1964 chrysler imperial convertible rare
- 1972 black runs & drives great body & interior vgood rear ac!
- 1938 chrysler imperial sedan--garage stored since 1956
- 1973 chrysler imperal, loaded, 37000 orig miles!! like new interior! 440 motor!!
- 1938 chrysler imperial sedan--garage stored since 1956
- 1962 chrysler imperial crown 6.8l(US $5,000.00)
Auto Services in New Jersey
Young Volkswagen Mazda ★★★★★
Wrenchtech Auto ★★★★★
Ultimate Collision Inc ★★★★★
Tang`s Auto Parts ★★★★★
Superior Care Auto Center ★★★★★
Sunoco ★★★★★
Auto blog
Dodge Viper saved from crusher by students, but will it last?
Tue, 16 Sep 2014The saga of the Washington state community college hoping to keep its allegedly pre-production Dodge Viper out of the maw of the crusher is going strong. Not only does the school still have the car, but there's a chance that the college might even get to keep it.
The whole situation flared up in March when the South Puget Sound Community College in Olympia, WA, received a notice from Chrysler Group that requested that the school's Viper be destroyed. The automaker had loaned the muscle car to it about a decade ago to use for educational purposes in its auto tech classes. With the Dodge growing long in the tooth, "it is unlikely that these vehicles offer any educational value to students," the company said in its press release on the matter.
However, the college balked at destroying its Viper, despite the fact it had signed a contract with Chrysler Group to do so. The school further claimed that its car was incredibly special because it was a pre-production example and just the fourth one made back in 1992. Although, as we pointed out at the time, the photos of the school's vehicle showed a coupe that looked like a newer Viper GTS.
Chrysler dealers terminated in bankruptcy still stuck in court
Mon, 14 Apr 2014Part of the deal for the federal bailouts of Chrysler and General Motors was that both organizations were required to trim their vast array of dealerships. This move did not sit well with the people that would be losing out on franchises, though, and in Chrysler's case, 148 of the shuttered dealers have fought for money they feel they are entitled to.
These dealers believe that they should be compensated by the federal government, as Chrysler wouldn't have trimmed its sales centers had it not been ordered to by Uncle Sam. Now, thanks to the ruling of three judges on the US Court of Appeals for the Federal Circuit, the dealers will get a chance to argue their point.
According to Automotive News, the dealers argue that the mandatory shuttering of dealers was unconstitutional, because the federal government was taking property without compensation. If the dealers are victorious, not only would the government be out millions of dollars, but a precedent could be set that would allow similarly closed GM dealerships to cash in.
Marchionne completed Fiat-Chrysler deal from a Florida beach
Fri, 03 Jan 2014Sergio Marchionne is the CEO of Fiat, which as you may have heard, has finally worked up a deal to finish acquiring the Chrysler Group after months of bargaining with the United Auto Workers and its VEBA healthcare trust, which owned just over 40 percent of the American brand. Where was Marchionne when the deal was finally hammered out? Well, not tucked away in a frigid Detroit board room until the wee hours of the morning.
Nope, one of the largest deals in automotive history was reportedly hammered out on the beach - at the home of a banker, in the Florida resort town of Vero Beach. Marchionne traveled to the home of Alain Lebec, a senior managing director at Brock Capital LLC, one of the advisory companies for the VEBA fund, where both sides met to make final arrangements in the $4.35-billion exchange. The location of the final deal, though, is nearly as remarkable as the pace with which it came about.
According to anonymous sources pinned down by Automotive News Europe, before the meeting, the two sides were meeting in Detroit as recently as December 19, which is where Fiat made one of its final revised offers. Naturally, the VEBA made a counter offer, which led Marchionne to initiate the Vero Beach meeting.