98 S10 Lowrider "bagged" And Slammed on 2040-cars
Marietta, Georgia, United States
1998 S-10 5spd with 73,000 miles, runs great. Custom exhaust system and cold Air intake. Vehicle sits 1" off the pavement and has around 8" of travel. Totally custom interior with billet steering wheel, gauges and switches for each wheel. Compressor switch mounted in armrest console. Bagged with compressor and fuel cell in bed. Shaved doors and tailgate, tinted windows, 20" wheels, vehicle has a very nice audio system with touch screen. Truck bed cover is custom with gas shocks. Needs a few things: Remote door actuators need work - power to drivers side door lock only - may be a relay or a new sending unit. Both actuators are brand new. Some sheet metal damage on lower passenger bed side (maybe $500 which is mostly paint) Fuel cell needs a new gasket at filler. This is a lot of truck for the money and you can drive it home. Mechanically it is 100% it just needs some attention and detail work. |
Chevrolet S-10 for Sale
Auto Services in Georgia
Wishen Motors ★★★★★
WILLIE & BATMAN AUTOMOBILE SERVICE ★★★★★
William Mizell Ford ★★★★★
W.T. Standard & Assoc. ★★★★★
Unlimited Motor Cars ★★★★★
Toyota Mall Of Georgia ★★★★★
Auto blog
GM warning 800,000 owners that their cars may need oil changes more frequently than they say
Fri, 05 Apr 2013The days of changing your engine oil every 3,000 miles are long gone thanks to most cars having automatic oil monitoring systems, but about 800,000 General Motors vehicles apparently have incorrect monitoring software that is leading to premature engine component wear. According to Autoweek, certain 2010-2012 Buick LaCrosse, Regal, Chevrolet Equinox and GMC Terrain models equipped with 2.4-liter four-cylinder engines could be going too long in between oil changes resulting in a higher-than-normal number of warranty claims for the engine's balance chain. The balance chain links the balance shaft to the crankshaft, and a worn one can produce higher noise levels.
As a fix, GM dealers will be reprogramming the software for the monitors in an effort to reduce the interval between oil changes, which varies based on driving habits and conditions. Through February 2015, the software update will be done at no cost to vehicle owners, but since this is not a recall, after that point, it will be up to the discretion of dealers as to whether or not they will charge for the service. What isn't immediately clear is whether GM plans on giving assistance to out-of-warranty customers who are experiencing engine issues from the worn chain.
Final C6 Corvette built in Bowling Green
Fri, 01 Mar 2013With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.
Experimental mid-engine XP-819 Corvette going up for auction
Sun, 17 Feb 2013It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.