2009(09) Cobalt We Finance Bad Credit! Buy Here Pay Here Low Down $1699 Ez Loan on 2040-cars
Bedford, Ohio, United States
Vehicle Title:Clear
For Sale By:Dealer
Engine:2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
Body Type:Sedan
Fuel Type:GAS
Make: Chevrolet
Warranty: Vehicle does NOT have an existing warranty
Model: Cobalt
Trim: LT Sedan 4-Door
Doors: 4 doors
Drive Type: FWD
Engine Description: 2.2L L4 MPI DOHC 16V
Mileage: 49,005
Number of Doors: 4
Sub Model: 4dr Sdn LT w/1LT
Exterior Color: Silver
Number of Cylinders: 4
Interior Color: Gray
Chevrolet Cobalt for Sale
- 2007(07) cobalt we finance bad credit! buy here pay here low down $799 ez loan(US $10,997.00)
- 2005(05) chevrolet cobalt beautiful silver! clean! must see! save huge!!!(US $9,595.00)
- 2008 chevrolet cobalt lt coupe *special edition*
- 2005 chevrolet cobalt ss with under 300 original miles(US $15,999.00)
- 2005(05) chevrolet cobalt beautiful blue exterior! clean! save huge!!!(US $8,895.00)
- Ss 2.4l cd trip computer power door locks power windows heated seat(s)
Auto Services in Ohio
Williams Norwalk Tire & Alignment ★★★★★
White-Allen European Auto Grp ★★★★★
Welch`s Golf Cart Inc ★★★★★
Vehicles Unlimited Inc ★★★★★
Tom`s Tire & Auto Service ★★★★★
Smith`s Automotive ★★★★★
Auto blog
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.
Final C6 Corvette built in Bowling Green
Fri, 01 Mar 2013With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.
Experimental mid-engine XP-819 Corvette going up for auction
Sun, 17 Feb 2013It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.