1984 Chevrolet M1009 Cucv Blazer K5 Military 4x4 A/c Radio on 2040-cars

US $13,300.00

Year:1984 Mileage:52436 Color: CAMO /
Bronze Metallic

Location:

Fontana, Kansas, United States

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 1

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 2

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 3

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 4

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 5

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 6

1984 Chevrolet M1009 CUCV Blazer K5 military 4x4 A/C Radio, US $13,300.00, image 7

Transmission:Automatic
Body Type:SUV
Vehicle Title:Clear
Engine:6.2L
Fuel Type:Diesel
For Sale By:Dealer

VIN: 1G8ED18JXEF194550 Year: 1984
Number of Cylinders: 8
Make: Chevrolet
Model: Blazer
Trim: CUSTOM DELUXE
Options: 4-Wheel Drive, CD Player
Drive Type: 4X4
Power Options: Air Conditioning
Mileage: 52,436
Sub Model: K5 BLAZER M1009
Exterior Color: CAMO
Warranty: Unspecified
Interior Color: Bronze Metallic

Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. ...

1984 Chevrolet M1009 CUCV Blazer

52436 original miles currently.

Email me and I can send a link to photobucket with all 65 pictures

Original Odometer was replaced at 49976 miles

-6400 GVW..

THis Blazer was built over the fall/winter of 2012 and finished in January 2013. THe Blazer had 48,581 miles when finished.

DRIVE TRAIN:

-6.2L J series diesel engine from a 1985 M1009 with 30K miles

- Before being put in the Blazer it had a rebuilt injection pump, new glow plugs, new head gaskets, new rear main seal, new front seal, new water pump, new harmonic balancer, re sealed oil pan, re sealed valve covers, new thermostat and new oil fill cap installed.., starts easy, runs great, no leaks, new oil and filter at time of build and again 2000 miles ago
-All new Gates belts and hoses

- THe glow plugs have been converted to 12V and still use the factory controller. However, there is a push button installed in case the factory controller ever fails and you need to get somewhere.

-Spin on fuel filter mod

-TH400 3 speed automatic, shifts through all gears fine, no slipping, no leaks, new fluid and filter at time of build

- There is also an additional heavy duty aftermarket cooler

-NP208 2 speed (high/low) chain driven transfer case. Shifts through all ranges fine. no leaks, output shaft seals and fluid new at time of build

-Corporate 10 bolt front axle:

-3.08 gears, open differential
-Ball joints are in good shape.

-All but the rod ends at the pitman arm were just replaced

-Wheel bearings checked and repacked

- Axle u-joints and driveshaft u-joints nice and tight

-New front brake pads at time of build

-Warn Style style 3/4 turn lock outs

-New Fluid at time of build

-Corporate 10 bolt rear axle, 3.08 gears, Eaton Gov-Lok

-New fluid at time of build

-new rear brake shoes at time of build

-Gov-lok works as it should

-Emergency brakes work as they should

Service brakes work great front and back. No pulling or dragging.

-Rear driveshaft had new greaseable u-joints installed

-Tires and Wheels

33x12.50x15 BF Goodrich AT KO mounted on the factory 15x8 steel wheels which have been sand blasted and repainted.

The spare is not matching, tire or wheel, but is like new and will get you wherever you may need.

Exterior Lighting:

-The Blazer has LMC's aftermarket heavy duty harness so it pulls the headlights power right from the battery.. This helps eliminate the common melted fuse block and makes sure your lights get the full voltage all the time.

-Sylvania Silverstar Headlights. Much brighter and whiter light.

-Aftermarket 55w off road lights

-all other bulbs were replaced with new stock bulbs.

-The front side maker lenses and rear tail light lenses were replaced with new aftermarket ones

-All Blackout lights work. All four bumper lights and the drive light

Interior lighting:

All factory interior lighting works as it should as do the lights on the aftermarket gauges.

Alternators:

Both alternators were completely rebuilt .

Instrumentation/Switches:

All factory dummy lights and gauges still work properly.

The speedometer was replaced because it started bouncing at higher speeds.

The Blazer also has mechanical oil pressure and coolant temperature gauges by Autometer .

All factory switches work properly, service lights, wiper, and blackout lights.

Glass/Weaherstripping:

All glass is in good shape.

THe front windshield has been replaced with one that has the shading up top and built in antenna for the radio. it also has a new seal and lock.

The vent windows have also had new seals installed.

The windows have been tinted as well. The front doors are 35%. The side and back glass are 20%

The doors had new GM window channel weatherstrip installed and new GM window seals installed inside and out

THe rear glass exterior window seal is new GM and the window weatherstrip in the shell is new aftermarket.

The glass in both mirrors is also good. There are also blind spot mirrors.

Upholstery and trim:

All 3 seats have been recovered with new vinyl from LMC and then recolored to the factory Bronze metallic

The door panels, arm rests, kick panels, and sun visors are original to the Blazer, but were re-colored as well so everything matched perfect

The dash pad was a brand new GM unit that was re-colored the factory Bronze metallic

The seat belts new LMC units front and back.

The Blazer also has an aftermarket 2 compartment locking center console with adjustable cup holders front and back

Paint/Coatings Interior and Exterior:

The Blazer has been repainted inside, outside, and in the engine compartment.

Prior to paint the interior was sanded and prepped for both paint and the spray on sound control. The parts that got coated were the cab to include the shell, floor front and back, behind the kick panels and the interior of the door shell. They were coated with Lizard Skin spray on sound control.

The same was also done to the whole engine bay to include the inside of the fenders, fender wells, core support, firewall and underside of hood. It helps with noise reduction and heat control.

Then, the engine bay was painted the same flat black as used on the 3 color Camo exterior and wheels.

The exterior was then sanded and primed using a nice Urethane primer, sanded, then primed with an epoxy primer.

The interior and exterior were then painted using GCI's Current Issue Lusterless OD green for the base coat. 2 coats inside and 3 outside.

The exterior then got 2 coats each of the black and brown, still GCI paint, to finish up the 3 color camo. The current issue patterns were used for reference.

The bumpers and grille were then blacked out.

Last for the exterior was the stenciling which includes the reg number, star, unit number, tire pressure and fuel type. Most are military correct, some are for what the owner wanted.

Last for the interior was the bed liner sprayed front to back on the floor, on the inside facing portion of the tailgate, and up to where the shell sits.

THe frame and undercarriage were in excellent shape and to preserve them they were coated with a petroleum based undercoating by Rusfre front to back top to bottom.

THE EXTRAS: Lift. a/c etc

LIFT:

THe Blazer has a 4 inch suspension lift by Tuff Country. The lift includes their 4 inch HD lift springs, rear blocks, raised steering arm, and 4 new Hydro Shocks. The sway bar was lowered and had new polyurethane bushings installed as well.

A/C

The AIR CONDITIONING is a Gen IV set up by Vintage Air. It allows a factory appearance on the inside and keeps the firewall clean on the outside. All but the condenser tucks up under the dash. To get all the specifics you can go to www vintage air dot com

The A/C does blow ice cold and the heater blows hot as well.

The compressor is mounted on custom brackets to allow the retention of the dual alternator set up and is driven off its own additional pulley that mounts inside the original crank pulley.

Radio:

The head unit is a Kenwood CD player with Bluetooth capabilities, USB port, and IPOD controls. IT also has a remote.

The rear speakers are Kenwood 4 way 6x9's in Sound ordnance boxes.

The front speakers are Sound Ordnance 2 way 3 1/2's in the factory locations

There is also a self enclosed amp/sub combo by Kenwood under the seat with an exterior wired remote (By the 4wd shifter on the floor).

I can get actual part number if need be, i just cant find the receipts right now

Towing goodies:

It does still have the factory pintle and trailer wiring.

The Blazer also has a Curt receiver hitch.

It also has a 7 way trailer plug with a Reese brake controller. The controller is mounted to the side of the center console.

Winch:

The winch is a Tiger Shark 9500 by Superwinch. The winch mount is integrated into the grille guard. The winch works great. It has been used a couple times, mainly to pull Jeeps out on some trails in Colorado (The son of the gentleman the Blazer was built for goes to college there.)

-There is a 12V power source mounted to the side of the center console

-New wiper motor

-DeeZee nerf bars

The average MPG for the Blazer on the Highway is 20-22. In town was never calculated.

I am sure I am forgetting things. I will try to post things as soon as I think of them, but don't hesitate to call or email if you have any questions or need pictures

Also, I do have a 6.5 turbo set up and a serpentine belt drive set up that can be bought at an addition cost on top of the Blazer purchase price. Installment can be arranged as well. The reserve price and buy it now price DO NOT include any of these items or installation of them

-Clear Oklahoma title.

I can transfer it into my dealerships name at the time of sale so I can print off 60 days tags if needed.

-Please call or email with any questions you may have or for more pictures..

913 757 3456

-Would not be worried to drive the Blazer anywhere. It has been from here, to Dallas, TX to Golden, Colorado for a few months, then back to Dallas.

Delivery can be arranged. I have had great luck with U-SHIP. I can check rates there if needed. buyer pays ALL shipping fees

If you would want myself to do it, I can at $1.55 per loaded mile or I can drive it out for $1.00 a mile plus my plane ticket home.

- Cash, bank checks, loan checks accepted. I prefer cash or bank check. Personal chacks can be used as well so long as I can get verification that funds or available or you wait until it fully clears

Chevrolet Blazer for Sale

Auto Services in Kansas

Ward`s Mobile Mechanics ★★★★★

Auto Repair & Service

Address: Piedmont

Phone: (316) 500-5678

V Werks ★★★★★

Auto Repair & Service

Address: 4610 Merriam Dr, Shawnee

Phone: (913) 362-4111

Terry`s Auto Sales & Salvage ★★★★★

New Car Dealers, Automobile Body Repairing & Painting, Automobile Parts & Supplies

Address: 401 W 1st St, Waverly

Phone: (785) 733-2231

Sutton-Kauffman Transmission ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Transmissions-Other

Address: 501 N Poplar St, Lyons

Phone: (620) 860-1418

Showroom Automotive ★★★★★

Auto Repair & Service, New Car Dealers

Address: 7478 S Broadway St, Haysville

Phone: (316) 522-2100

Riley`s Rescue ★★★★★

Auto Repair & Service, Automotive Roadside Service, Towing

Address: WEST And Central, Milan

Phone: (316) 200-1158

Auto blog

Why does the Corvette Stingray have so many vents? Here's why

Sun, 27 Jan 2013

Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.

Joe Flacco wins C7 Corvette along with MVP honors

Mon, 04 Feb 2013

As part of a longstanding tradition, the MVP of Super Bowl XLVII, Joe Flacco, quarterback for the Baltimore Ravens, was given a new car directly after the game and trophy celebrations. For 2013, that car is a 2014 Chevrolet Corvette Stingray, and it was presented to Flacco by Rick Flick of Banner Chevrolet, a dealership in New Orleans that was wiped out by Hurricane Katrina in 2005 before returning to prominence as the only Chevy dealer in Orleans Parish.
Last year, Super Bowl MVP Eli Manning took home a 2012 Corvette GS Centennial Edition. Manning also won in 2008, when he selected a Cadillac Escalade Hybrid as his reward. In 2011, quarterback Aaron Rodgers accepted the keys to a Camaro convertible.
Though we're most definitely an auto-obsessed group, we did watch the Big Game along with nearly everyone else in America. And we've gotta say, as if winning the Super Bowl and receiving the Tiffany-designed Pete Rozelle Trophy wasn't enough for the multi-millionaire MVP athletes, a brand-new C7 seems like an awfully generous prize. Scroll down below for an official announcement from General Motors.

Chevy to show redesigned Captiva in Geneva, will it come to US rental lots?

Wed, 27 Feb 2013

Unless you're renting a car or driving through Orlando, Florida (the rental car capital of the US), you'll probably never see a Chevrolet Captiva - the rebadged, fleet-only version of the old Saturn Vue - on our roads, but this crossover is popular in many other parts of the world. As such, Chevrolet announced that the Captiva will be getting an update for 2013, which will be unveiled next week at the Geneva Motor Show.
Coming off a pretty extensive refresh in 2011, the 2013 model year will bring even more changes to the Captiva like LED taillights, new 18-inch wheels and revised fascias with a new grille and fog lights up front and inset chrome exhaust outlets at the rear. New interior features include heated rear seats, dual-zone climate control as well as available options on some of the upper trim levels such as leather seating and keyless entry and start. We have yet to hear back from Chevrolet as to whether or not the updated Captiva will be making its way to a rental lot near you, as the model is only available in the US to fleet buyers.
Alongside the updated Captiva, Chevy is also showing off its new Trax in Europe, where the subcompact crossover will go on sale this spring. GM's press release for these two Geneva-bound models is posted below.