1955 Chevy 4 Door Sedan, 95 % Solid, Alot Work Done To This Car on 2040-cars
Plant City, Florida, United States
Vehicle Title:Clear
Make: Chevrolet
Drive Type: STD
Model: Bel Air/150/210
Mileage: 99,999
Trim: 210
WHAT I HAVE HERE , IS A VERY NICE 55 CHEVY WITH ALOT OF WORK AND MONEY DONE TO IT, FRAME WAS BLASTED AND PAINTED, COMPLETLY REBULT, WITH ALOT OF NEW PARTS, WITH AADCO BIG SWAY BARS FRONT AND BACK, ,LEAF SPRINGS FLIPPED TO INSIDE, 3 INCH LOWERING BLOCKS IN REAR,FRONT 2 INCH DROP SPINDLES, NEW 2 INCH DROP SPINGS, REBULT FRONT END. DIS BRAKES FRONT AND BACK, 8.8 FORD REAR END, 3.73,POSI NARROWED 3 INCHES BOTH SIDES,FRONT RACK AND PINION STEERING, 4 NEW SHOCKS, NEW CAMARO 18 INCH STEEL WHEELS WITH ALMOST NEW TIRES,,ALL NEW BUSHINGS AND BEARINGS,SIDE ENGINE MOUNTS, TRANS MEMBER, SHORTED TILT COLUMM S10, 95 CAMARO BRAKE BOOSTER AND MASTER, NEW ALL NEW BRAKES LINES NOT INSTALLED, THE CAR HAS BIN TUB IN THE REAR, VERY NICE JOB, NEW REFABBED TRUNK FLOOR, VERY NICE JOB,, THE BODY IS VERY NICE AND SOLID BODY. FLOOR PANS MINT NO RUST OR PATCH, FLOOR BRACE`S VERY SOLID, ROCKER VERY NICE, RIGHT ROCKER SIDE HAS DAMAGE ON FRONT, I HAVE NEW PANEL TO REPAIR IT, DOORS VERY NICE AND SOLID, VERY LITTLE RUST UNDER RIGHT DOOR, NOT BAD, I HAVE A MINT RIGHT DOOR GO`S WITH THE CAR,, NICE R/F FENDERS, LEFT FENDER HAS LITTLE DAMAGE , I HAVE A GOOD LEFT FENDER GO`S WITH THE CAR, THE OLD SIDE GLASS NEED`S REPLACE. GOOD REAR AND FRONT GLASS,I HAVE OLD GLASS FOR A PATERN, ALL DOOR PART ARE THERE,, NICE FOOF, RUST FREE AND STRAIGHT, OVER ALL THE CAR IS VERY STRAIGHT. LITTLE BOW ON CENTER OF HOOD, EASY FIX,,NICE TRUNK LID, LITTLE REPAIR ON BOTTOM INTER, NICE JOB, ALL SEAT ARE THERE,, NO INSIDE DOOR PANELS,, A LOT OF MONEY AND TIME WAS PUT IN THIS CAR, CLEAR FL TITLE,, THERE IS OVER $8,000.00 IN THIS CAR,, CALL FOR MORE DETAILS, I AM GOING UP THE EAST COST FROM FL TO PA , I CAN DELIVER IT FOR $350.00 , CAR HAS TO BE PAID FOR IN 7 DAYS, 813 441 4192
On Apr-09-13 at 14:06:11 PDT, seller added the following information:
AFTER $2,100.00 THE RESERVE WILL BE MET,,,THE HIGH BIDDER WILL GET THE CAR, SO BID AWAY
Chevrolet Bel Air/150/210 for Sale
- 1955 chevrolet bel air
- 1955 chevrolet 210 bel air trim(US $35,800.00)
- 2 owner, california black plate, 1957 chevy bel air convertible, excellent shape(US $70,000.00)
- 1954 chevy sedan delivery 350/350 holley ps pdb tilt power windows 10 bolt
- 1954 chevrolet belair sport coupe
- Florida 1955 chevy bel air 2-door hard top show quality classic collector car
Auto Services in Florida
Wildwood Tire Co. ★★★★★
Wholesale Performance Transmission Inc ★★★★★
Wally`s Garage ★★★★★
Universal Body Co ★★★★★
Tony On Wheels Inc ★★★★★
Tom`s Upholstery ★★★★★
Auto blog
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.
2014 Chevrolet Corvette Stingray Convertible gives us a couple of looks
Sat, 02 Mar 2013Put away your pixel paintbrushes, kids. Pack up your Photoshop. This is the real-deal 2014 Chevrolet Corvette Stingray Convertible in its first official images. The droptop Chevrolet will roll into the bright lights of the Palexpo exhibition at next week's Geneva Motor Show, a four-wheeled statement of intent that General Motors is serious about taking its Corvette franchise global.
Chevy isn't providing anything in the way of further details with these two shots, but we've learned at least a couple of things about the car shown here. First off, the example seen in these images is fitted with the optional Z51 Performance Package - something that isn't immediately evident because there's no sign of the coupe model's prominent ductwork on its rear haunches. In order to accommodate the power folding hard tonneau cover, the vents that feed the transmission and differential coolers have been relocated to the underside of the car. The dark paint color on this example also does a good job of muting the contrasting black front fender vents and hood opening - Z51-spec design details that have proven to be somewhat controversial.
One other thing to note: These two shots also display the Stingray wearing different alloy wheels than the split five-spoke design shown at the hardtop's Detroit Auto Show unveiling in January. The simpler, thin five-spoke wheels should do a good job of showing off the Z51's upgraded brakes, and they'll be optional on the coupe as well.
UAW to vote on strike at Kentucky Corvette plant
Tue, 08 Apr 2014The current wait time for a new Chevrolet Corvette Stingray is well, not short. With word of a strike at the Bowling Green, KY factory responsible for seventh-generation sports car, though, that wait time could end up growing substantially.
Now, a strike is still a ways off. UAW Local 2164, which represents the 800 workers responsible for screwing the Corvette together, is set to vote on authorizing a strike today, but even if the employees give the action a go, it's far from a sure thing. According to The Tennessean, both regional and national union officials would need to put their stamp of approval on strike action.
"The membership has to vote to strike, but it's just a step in the process," said Gary Casteel, the UAW's Region 8 director and one of the people that would need to authorize a strike action. Casteel told The Tennessean, "It's purely a local situation, though. They are having some issues with the local management."