2008 Bmw 535i Base Sedan 4-door 3.0l on 2040-cars

Auto blog

2014 BMW 4 Series drops its top, priced from $48,750*

BMW will debut its new 2014 4 Series Convertible at the Los Angeles Auto Show in November, and after seeing plenty of spy shots and, most recently, some leaked images, we now have all the official details. To no one's surprise, the 4 Series convertible is, essentially, a topless version of BMW's new-for-2014 4 Series coupe, and will be offered in the United States in the same 428i and 435i guises.
On the base end, that means the 428i Convertible arrives with the company's 2.0-liter turbocharged inline four-cylinder engine, good for 240 horsepower and 255 pound-feet of torque, and available with either rear- or all-wheel drive. BMW says the 428i will sprint to 60 miles per hour in a respectable 6.2 seconds. For folks in need of more thrust, BMW will happily sell you a 435i Convertible, available only with rear-wheel drive, powered by a 3.0-liter, twin-turbocharged inline-six that produces 300 hp and 300 lb-ft of twist. Hitting 60 mph in the 435i will take roughly five and a half seconds with the standard eight-speed auto. Curiously, BMW did not mention anything about a six-speed manual transmission for either model, so looks like this droptop might be an auto-only affair. We've contacted BMW for confirmation, so we'll keep you posted.
Like the 3 Series Convertible it replaces, the 4 Series uses a three-piece folding hardtop configuration, and BMW says that added sound deadening reduces audible wind noise by about two decibels. Folding the automatic roof takes just 20 seconds, and can be done at speeds up to roughly 11 mph. For chilly, top-down driving (something we're big fans of), there are now three-temperature neck warmers for the front seats - just like what Mercedes-Benz offers with its AirScarf system.

Audi S3 pitted against BMW M135i in track battle

Audi and BMW have long been enemies on both the road and the track, with their respective M and S/RS lines duking it out to the delight of auto enthusiasts everywhere. In this video from Evo, two of the rivalry's newest combatants take to the track - the Audi S3 and the BMW M135i.
The new Audi S3, which is finally coming to America, throws down with a 2.0-liter, turbocharged four-cylinder. 290 horsepower and 280 pound-feet of torque are deployed to a Quattro all-wheel-drive system via a six-speed, S-Tronic dual-clutch transmission, allowing the five-door Audi to scamper to 60 in under five seconds.
The BMW, which Americans will know as a long-roof version of the new M235i Coupe, comes to the track with 320 ponies and 331 lb-ft of torque. That's a good bit more than the Audi, but the M135i has only two wheels to send its power to, an eight-speed single-clutch automatic (a six-speed manual is available) and a slightly higher curb weight.

BMW X4 reclaims dash of utility with Clemson student project [w/videos]

BMW seems willing to exploit every automotive niche it can find with creations like the four-door, 'crossover coupe' X4 and X6. Of course, these designs come with a compromise. That svelte fastback means that they just can't haul as much cargo as a more traditional, boxier hatchback. Fortunately, students at Clemson University's International Center for Automotive Research might have a novel solution: the engineering graduate program has turned the crossover into a unique pickup.
Dubbed Deep Orange 4 concept, this functional prototype has an enclosed cargo area with a sliding glass panel that opens up to expose a pickup bed if more room is needed. Think of it as the GMC Envoy XUV of German crossovers. This isn't just an X4 with its roof hacked off, though. The students actually started with an X3 and grafted on this top later in addition to the two barn doors for access to the bed.
To make this project even more impressive, this pickup-crossover could conceivably be produced. The graduate students conducted an in-plant analysis of BMW's manufacturing abilities and went back to the university to create a plan for a low-volume vehicle that could actually be built. "The students working on this phase of the project did an excellent job of keeping costs down while finding optimal integration opportunities," said Rich Morris, vice president of assembly at BMW Manufacturing, in the university's release.