1997 Acura Integra Type R Built Motor And Great Track Suspension Clean Recaros on 2040-cars
Redwood City, California, United States
|
I purchased the car from an owner in WA in NOV of 2012 and have owned it in CA. Car currently has about 103K miles on it. I've taken it to about 6 trackdays. Most of the description below is from the previous owner with me adding things where they have changed or been updated. This is a very capable track car and can be street driven with a full interior, clean trunk. Car will get you 25mpg regular driving.
1997 Integra Type-R #0110 Clean WA state title The good: Clean Title Straight body No major damage Clean Interior (no smoking/pets) Well maintained Comes with lots of extras, including rebuilt VIN matching B18C5 block The bad: Couple small scuffs/nicks/scratches on exterior Front lip has a big crack in it, together now with a brace and ductape Front bumper, hood & fenders replaced by previous owner after front-end collision (OEM parts) Story: This is a well maintained 1997 Integra Type-R with a number of modifications, but also included are a majority of the OE parts required to return the car to near-stock. #0110 was purchased from the original owner in 2003 100% stock minus the JDM 16 wheels and modified Koni shocks. #0110 was my daily driver until 2005 at which point she went under the knife for a 2.0L track-car build. #0110 attended ITR Expo-5 in Omaha Nebraska in 2005, and has been a garage queen and occasional weekend car since. Since I took ownership in 2003, #0110 has attended about a dozen HPDEs, and just about as many passes at the drag strip. I am selling #0110 because Im just not getting the enjoyment out of her that I used to. I have a new toy to occupy my time (and money). The engine build started in 2005. The 2.0L block now has about 25,000 miles, but despite its age the engine is still strong. I touched up the tune in early June 2012 and made 233whp and 159wtq on a DynoJet, which are the highest numbers yet. Before the dyno compression was 230/250/250/240, so the engine is healthy but starting to show its age. The oil is changed every few months (~500 miles) with Mobil1 5w30 Synthetic with OEM filter (15400-PLM-A01 Filtech). Valve adjustments are performed every-other oil change. The car still has the factory equipped Air Conditioning (charged) but needs a belt to operate. * Car actually will need the idler bracket and belt for AC to work. #0110 was re-sprayed inside/outside in 2002 with DuPont Championship White paint by previous owner after a front-end collision. All work was completed at a well-known body shop with all components removed before paint, including glass. Replacement parts were all OEM from a donor car, including bumper, hood and fenders. Included with the vehicle purchase are pictures of the donor car and full receipts of the work performed. Other than the missing VIN tags on the bumper/fenders/hood, you would never know this car was in an accident. Exterior Condition: Make no mistake, this car has been tracked. Ive hit a few cones with the front bumper, and consequently there have been a slowly increasing number of scuffs and faint paint cracks forming on the front bumper. This damage is not noticeable from +10ft. There are a couple minor dings/chips, I know where they are and you probably wont see them unless you look hard. Other than that, there are no dents or damage to the car. Interior Condition: Carpets are a little worn, but still in good condition for the age of the car. Seats are in great shape, passenger seat has a small 2 tear (pictured below), other than that no scuffs/stains/rips. #0110 has the original badge/armrest. Non-smoker no Pets. *I've sold the stock seats, currently has recaro JDM Seats in very good condition, 9/10. Bolt-Ons: Custom 3.5 Aluminum Intake w/3.5 > 6 Velocity Stack + K&N Filter Omni 70mm TB port matched to the stock ITR intake manifold Skunk2 MegaPower Header T1R Resonated Testpipe T1R 70R 70mm (2.75) catback exhaust. *Currently has an APEXI 70mm WS2 muffler to be slightly quieter, still have the T1R muffler. Shortblock *assembled in 2005 by Earl Laskey (RIP)*: 85mm B18C1 block with Benson sleeves, work performed by Dan Benson @ Benson Machine CP 12.0:1 forged pistons Eagle H-Beam connecting rods with ARP2000 bolts ACL rod & main bearings 87.2mm GSR Crankshaft micropolished and balanced by Dan Benson @ Benson Machine Baffled Oil Pan ARP Head Studs Stock motor mounts w/urethane inserts Cylinder Head: PR3 ITR head with 85mm chambers Deshrouded valve reliefs Custom valve grind 0.008 off surface Stock ITR ports Skunk2 Pro-series Stage 3 camshafts Skunk2 Pro-series Cam Gears SuperTech Valves (std. size) SuperTech Valvesprings SuperTech Titanium Retainers Cometic 85mm headgasket Greddy High-Strength Timing Belt Crankcase EVAC / Catch Can: Pulls vacuum (max -7 inhg) on the crankcase for improved ring seal and reduced blow-by through a slash-cut exhaust bung Custom 1800cc sealed catch-can made from 0.090 6061 Aluminum Two -10 AN w/Pro-Lite 350 lines to the back of the block (-10 AN fittings) One -10 AN to Barbed Fitting for line to exhaust slash-cut / EVAC One barbed fitting to valvecover One -6 AN w/Pro-Lite 350 line drainback to block Drivetrain: 97 ITR S80 Transmission w/OEM ITR LSD *matching VIN* ATS 4.929 Final Drive Exedy Stage-2 3puck lightweight sprung clutch Fidanza 7.5lb Flywheel New seals/bearings installed in January 2008 *I recently at 100K Installed an aluminum radiator alpha skunk2 *I recently at 100K also rebuilt the transmission as there was a grind. A new 3rd gear was purchased. Installed a GSR 5th gear, and brand new syncrotech carbon syncros for all gears. Suspension/Brakes: *100K Hawk HP Plus pads front and rear Brembo Blank rotors (front & rear) ATE SuperBlue brake fluid Groodrich SS brake lines *I recently installed at about 100K Eibach Multi-Pro RS-2 with 450F/550R spring rates *ALso put on skunk2 pro series upper control arms for more camber in front *Blacktracks rear camber adjusters. Alignment is now 0 toe front slight toe-in rear with -3.2F - 2.2R settings Wheel/Tire: JDM ITR 16 wheels in championship white Falken 912s i think 215 series tires with lots of tread remaining. Electronics/Fuel: OBD2a-OBD1 jumper harness P72 ECU with eCtune (tuned by me, license will transfer to new owner) RDX 410cc injectors w/Xenocron adapters (plug-and-play connectors) Replaced Distributor in 2005 with engine build NGK Blue Plug Wires (installed 2005) New Distributor cap/rotor (2011) New NGK BKR7E Plugs every 5,000 miles Appearance/Interior: Luv2Boost dual-pod inner bezel w/Innovate MTX-L Wideband and X-Line electronic Oil Pressure Gauge JDM ITR red shift boot Spoon Sports Black Duracon shift knob Spoon Sports brake/clutch reservoir covers Spoon Sports radiator cap OEM parts: (come with car, not installed) *OEM 1997 B18C5 ITR shortblock w/matching VIN* with new bearings, seals and water/oil pumps OEM 1997 ITR exhaust manifold OEM 1997 ITR Intake Arm & Resonator Box OEM 1997 ITR exhaust (catback) OEM 1997 ITR springs OEM 1997 P73 ITR ECU OEM 1997 ITR Throttle Body Misc. Extras: Original Window Sticker Original ITR Special Edition Key in great condition (I never used it .) 1997 Acura Body Repair Manual 1997 Acura Integra Type-R Service Manual Supplement This car could be returned to mostly stock very easily. The cylinder head currently on the car has enlarged bores to match the 85mm block, therefore it cannot be installed on the rebuilt OEM 81mm shortblock. If the new owner wishes to install the OEM 81mm shortblock, a PR3 VTEC cylinder head will be needed. Link to Video: http://youtu.be/GGs2sGkmOvk |
Acura Integra for Sale
1991 acura integra rs a rare treat for a honda enthusiast!!! 59k miles 5 speed(US $6,500.00)
1997 acura integra ls hatchback 3-door 1.8l(US $2,100.00)
2001 acura integra 4 door gsr turbo 300whp(US $15,000.00)
Acura integra : low miles very clean very dependable 4 cylinder
1993 acura integra ls hatchback 3-door 1.8l(US $2,500.00)
1990 acura integra rs sedan 4-door 1.8l(US $2,400.00)
Auto Services in California
Z Best Body & Paint ★★★★★
Woodman & Oxnard 76 ★★★★★
Windshield Repair Pro ★★★★★
Wholesale Tube Bending ★★★★★
Whitney Auto Service ★★★★★
Wheel Enhancement ★★★★★
Auto blog
Watch an Acura NSX prototype lap the track at Mid-Ohio
Sun, 04 Aug 2013As promised, Acura trotted its NSX prototype out to the mass of waiting fans ahead of today's Honda Indy 200 IndyCar race at Mid-Ohio. The hybrid supercar took to the track for a fast lap, and Acura was kind enough to attach a score of cameras to the car in order to share the event with the rest of the world.
The blue-wrapped NSX looks pretty darn good on a race track, if we do say so ourselves, and its V6 engine, coupled with its three electric motors and lithium-ion battery pack, sounds awfully sweet at full song. The automaker is promising to release its new NSX in 2015, which is still quite a ways away, so we don't expect this exhibition lap to be the last time we see a prototype in action ahead of a production debut.
Want to see the video? Of course you do. Scroll down to see the NSX take to the track like a fish takes to water.
Reliving the Acura NSX debut, 25 years later
Sat, 03 May 2014The Acura NSX might be one of the most important Japanese cars ever created. The Land of the Rising Sun had already established that it could make very competent performance vehicles when the NSX debuted in 1989, but Honda's two-seater was the first one that looked to the world like a true contender against Ferrari and Porsche, thanks to its cutting-edge technology. The Acura had an all-aluminum monocoque chassis, a beautifully low-slung body and a quick-revving V6 with an 8,000-rpm redline. This quintessential Japanese sports coupe celebrates its 25th anniversary this year, and Autoweek recognizes it in a fantastic piece chronicling the model's US launch.
The story begins in February 1989 at the Chicago Motor Show where the car debuted. The day before the show opened, the concept still didn't have a name. The Japanese development team referred to it as New Sports, and the American Acura executives decided to add eXperimental to the end. The moniker NSX just stuck afterwards.
The article paints a fantastic portrait of the car and the company at the time. Honda had something to prove with the NSX. To succeed, the coupe had to be the best, and when the American press finally got a hold of it, they drowned it in accolades. Of course, Acura has a new American-built NSX on the way, and it has colossal legacy to live up to. This piece is definitely worth reading to understand why.
Acura launches ad spots for Seinfeld's Comedians in Cars Getting Coffee
Thu, 19 Dec 2013Acura and Jerry Seinfeld are expanding their partnership as season three of the comedian's web series, Comedians in Cars Getting Coffee, prepares to debut. Seinfeld has paired with director Barry Sonnenfeld to create a series of ads for the luxury brand showcasing the new Acura RLX and MDX.
There are eight spots, written by Seinfeld and directed by Sonnenfeld, that seemingly mock advertisements of the 1960s, with a deep-voiced, smooth-talking host highlighting the cars in question. It's all very folksy, Leave it to Beaver style humor. We'd be lying, though, if we said we weren't reminded a bit too forcefully of Dodge's successful range of Will Ferrell ads when watching the eight Acura spots.
"My idea for Comedians In Cars Getting Coffee was to show this certain aspect of the stand-up comedy world in a way that comedy fans would enjoy experiencing as if they were there," said Seinfeld. "There is absolutely no doubt that without Acura's support I would not have been able to continue beyond the initial experiment. And now Acura has enabled me to extend the concept by creating ads that fit the comedy tone of the show."